bsp.mk

################################################################################
# \file bsp.mk
#
# \brief
# Define the KIT-XMC72-EVK-MUR-43439M2 target.
#
################################################################################
# \copyright
# Copyright 2021-2024 Cypress Semiconductor Corporation (an Infineon company) or
# an affiliate of Cypress Semiconductor Corporation
#
# SPDX-License-Identifier: Apache-2.0
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
################################################################################

ifeq ($(WHICHFILE),true)
$(info Processing $(lastword $(MAKEFILE_LIST)))
endif

# Any additional components to apply when using this board.
# Use a default CM0+ image (XMC7x_CM0P_SLEEP). This can be swapped for a
# different pre-built image or removed if custom built project.
BSP_COMPONENTS:=XMC7x_CM0P_SLEEP WIFI_INTERFACE_SDIO

# Any additional defines to apply when using this board.
BSP_DEFINES:=CY_USING_HAL CYBSP_WIFI_WL_REG_ON_GPIO_DRIVE_MODE=CYHAL_GPIO_DRIVE_STRONG CYBSP_WIFI_WL_HOSTWAKE_DRIVE_MODE=CYHAL_GPIO_DRIVE_PULLUP CYBSP_WIFI_WL_HOSTWAKE_INIT_STATE=WHD_TRUE CYBSP_WIFI_HOST_WAKE_IRQ_EVENT=CYHAL_GPIO_IRQ_FALL

# Path to the flash loaders to patch for this board
CY_QSPI_FLM_DIR=$(MTB_TOOLS__TARGET_DIR)/config/FlashLoaders/

# Path to the patched flash loaders for this board
CY_QSPI_FLM_DIR_OUTPUT=$(MTB_TOOLS__TARGET_DIR)/config/GeneratedSource/

ifneq (,$(filter XMC7x_CM0P_SLEEP, $(BSP_COMPONENTS)))
BSP_LINKER_CORE:=linker
else
BSP_LINKER_CORE:=linker_d
endif
ifeq ($(TOOLCHAIN),GCC_ARM)
	BSP_LINKER_SCRIPT_EXT:=ld
else ifeq ($(TOOLCHAIN),ARM)
	BSP_LINKER_SCRIPT_EXT:=sct
else ifeq ($(TOOLCHAIN),IAR)
	BSP_LINKER_SCRIPT_EXT:=icf
endif
MTB_BSP__LINKER_SCRIPT=$(MTB_TOOLS__TARGET_DIR)/COMPONENT_$(MTB_RECIPE__CORE)/TOOLCHAIN_$(TOOLCHAIN)/$(BSP_LINKER_CORE).$(BSP_LINKER_SCRIPT_EXT)
$(info "Using linker $(MTB_BSP__LINKER_SCRIPT)")
################################################################################
# ALL ITEMS BELOW THIS POINT ARE AUTO GENERATED BY THE BSP ASSISTANT TOOL.
# DO NOT MODIFY DIRECTLY. CHANGES SHOULD BE MADE THROUGH THE BSP ASSISTANT.
################################################################################

# Board device selection. MPN_LIST tracks what was selected in the BSP Assistant
# All other variables are derived by BSP Assistant based on the MPN_LIST.
MPN_LIST:=XMC7200D-E272K8384 LBEE5KL1YN
DEVICE:=XMC7200D-E272K8384
ADDITIONAL_DEVICES:=CYW43439KUBG
DEVICE_COMPONENTS:=43439 CAT1 CAT1C CAT1C8M HCI-UART MURATA-1YN
DEVICE_CYW43439KUBG_DIE:=4343A2
DEVICE_CYW43439KUBG_FLASH_KB:=0
DEVICE_CYW43439KUBG_SRAM_KB:=512
DEVICE_LIST:=XMC7200D-E272K8384 CYW43439KUBG
DEVICE_TOOL_IDS:=bsp-assistant bt-configurator device-configurator dfuh-tool library-manager memory-analyzer project-creator qspi-configurator smartio-configurator
DEVICE_XMC7200D-E272K8384_CORES:=CORE_NAME_CM0P_0 CORE_NAME_CM7_0 CORE_NAME_CM7_1
DEVICE_XMC7200D-E272K8384_DIE:=TVIIBH8M
DEVICE_XMC7200D-E272K8384_FLASH_KB:=8384
DEVICE_XMC7200D-E272K8384_SRAM_KB:=1024
RECIPE_DIR:=$(SEARCH_recipe-make-cat1c)