Disclaimer: This is a community code example (CCE) released for the benefit of the community users. These projects have only been tested for the listed BSPs, tools versions, and toolchains documented in this readme. They are intended to demonstrate how a solution / concept / use-case can be achieved on a particular device. For official code examples, please click here.
This code example demonstrates how to extend the number of SAR ADC channels to virtually any available analog pin in the device without much impact on the sampling speed. It is implemented totally in hardware by using the global analog mux, instead of the SAR mux sequencer.
- ModusToolbox™ software v3.0 or later (tested with v3.0)
- Board support package (BSP) minimum required version for:
- PSoC™ 6 MCU: v4.0.0
- Programming language: C
- Associated parts: All PSoC™ 6 MCU parts
- GNU Arm® embedded compiler v10.3.1 (
GCC_ARM) - Default value ofTOOLCHAIN
- PSoC™ 6 Wi-Fi Bluetooth® Prototyping Kit (
CY8CPROTO-062-4343W) - PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit (
CY8CKIT-062-WIFI-BT) - PSoC™ 62S2 Wi-Fi Bluetooth® Pioneer Kit (
CY8CKIT-062S2-43012) – Default value ofTARGET
This example uses the board's default configuration. See the kit user guide to ensure that the board is configured correctly.
By default, this code examples uses Port 9, Port 10 and Port 12 as analog inputs (total of 24 analog channels for the SAR ADC). But you can virtually use any available analog pin from your hardware. You might need to apply a voltage between GND and the maximum allowed voltage in the SAR ADC to test this code example.
Install a terminal emulator if you don't have one. Instructions in this document use Tera Term.
Create the project and open it using one of the following:
In Eclipse IDE for ModusToolbox™ software
-
Click the New Application link in the Quick Panel (or, use File > New > ModusToolbox™ Application). This launches the Project Creator tool.
-
Pick a kit supported by the code example from the list shown in the Project Creator - Choose Board Support Package (BSP) dialog.
When you select a supported kit, the example is reconfigured automatically to work with the kit. To work with a different supported kit later, use the Library Manager to choose the BSP for the supported kit. You can use the Library Manager to select or update the BSP and firmware libraries used in this application. To access the Library Manager, click the link from the Quick Panel.
You can also just start the application creation process again and select a different kit.
If you want to use the application for a kit not listed here, you may need to update the source files. If the kit does not have the required resources, the application may not work.
-
In the Project Creator - Select Application dialog, choose the example by enabling the checkbox.
-
(Optional) Change the suggested New Application Name.
-
The Application(s) Root Path defaults to the Eclipse workspace which is usually the desired location for the application. If you want to store the application in a different location, you can change the Application(s) Root Path value. Applications that share libraries should be in the same root path.
-
Click Create to complete the application creation process.
For more details, see the Eclipse IDE for ModusToolbox™ software user guide (locally available at {ModusToolbox™ software install directory}/docs_{version}/mt_ide_user_guide.pdf).
In command-line interface (CLI)
ModusToolbox™ software provides the Project Creator as both a GUI tool and the command line tool, "project-creator-cli". The CLI tool can be used to create applications from a CLI terminal or from within batch files or shell scripts. This tool is available in the {ModusToolbox™ software install directory}/tools_{version}/project-creator/ directory.
Use a CLI terminal to invoke the "project-creator-cli" tool. On Windows, use the command line "modus-shell" program provided in the ModusToolbox™ software installation instead of a standard Windows command-line application. This shell provides access to all ModusToolbox™ software tools. You can access it by typing modus-shell in the search box in the Windows menu. In Linux and macOS, you can use any terminal application.
The "project-creator-cli" tool has the following arguments:
| Argument | Description | Required/optional |
|---|---|---|
--board-id |
Defined in the <id> field of the BSP manifest |
Required |
--app-id |
Defined in the <id> field of the CE manifest |
Required |
--target-dir |
Specify the directory in which the application is to be created if you prefer not to use the default current working directory | Optional |
--user-app-name |
Specify the name of the application if you prefer to have a name other than the example's default name | Optional |
The following example clones the "AMux SAR ADC" application with the desired name "AMuxSAR" configured for the CY8CKIT-062-WIFI-BT BSP into the specified working directory, C:/mtb_projects:
project-creator-cli --board-id CY8CKIT-062-WIFI-BT --app-id cce-mtb-psoc6-amux-sar-adc --user-app-name AMuxSAR --target-dir "C:/mtb_projects"
Note: The project-creator-cli tool uses the git clone and make getlibs commands to fetch the repository and import the required libraries. For details, see the "Project creator tools" section of the ModusToolbox™ software user guide (locally available at {ModusToolbox™ software install directory}/docs_{version}/mtb_user_guide.pdf).
To work with a different supported kit later, use the Library Manager to choose the BSP for the supported kit. You can invoke the Library Manager GUI tool from the terminal using make library-manager command or use the Library Manager CLI tool "library-manager-cli" to change the BSP.
The "library-manager-cli" tool has the following arguments:
| Argument | Description | Required/optional |
|---|---|---|
--add-bsp-name |
Name of the BSP that should be added to the application | Required |
--set-active-bsp |
Name of the BSP that should be as active BSP for the application | Required |
--add-bsp-version |
Specify the version of the BSP that should be added to the application if you do not wish to use the latest from manifest | Optional |
--add-bsp-location |
Specify the location of the BSP (local/shared) if you prefer to add the BSP in a shared path | Optional |
Following example adds the CY8CPROTO-062-4343W BSP to the already created application and makes it the active BSP for the app:
~/ModusToolbox/tools_{version}/library-manager/library-manager-cli --project "C:/mtb_projects/MyHelloWorld" --add-bsp-name CY8CPROTO-062-4343W --add-bsp-version "latest-v4.X" --add-bsp-location "local"
~/ModusToolbox/tools_{version}/library-manager/library-manager-cli --project "C:/mtb_projects/MyHelloWorld" --set-active-bsp APP_CY8CPROTO-062-4343W
In third-party IDEs
Use one of the following options:
-
Use the standalone Project Creator tool:
-
Launch Project Creator from the Windows Start menu or from {ModusToolbox™ software install directory}/tools_{version}/project-creator/project-creator.exe.
-
In the initial Choose Board Support Package screen, select the BSP, and click Next.
-
In the Select Application screen, select the appropriate IDE from the Target IDE drop-down menu.
-
Click Create and follow the instructions printed in the bottom pane to import or open the exported project in the respective IDE.
-
-
Use command-line interface (CLI):
-
Follow the instructions from the In command-line interface (CLI) section to create the application.
-
Export the application to a supported IDE using the
make <ide>command. -
Follow the instructions displayed in the terminal to create or import the application as an IDE project.
-
For a list of supported IDEs and more details, see the "Exporting to IDEs" section of the ModusToolbox™ software user guide (locally available at {ModusToolbox™ software install directory}/docs_{version}/mtb_user_guide.pdf).
-
Connect the board to your PC using the provided USB cable through the KitProg3 USB connector.
-
Open a terminal program and select the KitProg3 COM port. Set the serial port parameters to 8N1 and 115200 baud.
-
Program the board using one of the following:
Using Eclipse IDE for ModusToolbox™ software
-
Select the application project in the Project Explorer.
-
In the Quick Panel, scroll down, and click <Application Name> Program (KitProg3_MiniProg4).
Using CLI
From the terminal, execute the
make programcommand to build and program the application using the default toolchain to the default target. The default toolchain is specified in the application's Makefile but you can override this value manually:make program TOOLCHAIN=<toolchain>Example:
make program TOOLCHAIN=GCC_ARM -
-
After programming, the application starts automatically. Confirm that the UART terminal displays as shown in Figure 1.
Figure 1. Terminal output on SAR ADC measurements in counts
-
Change the voltage in a given pin and check the results in the terminal. If you don't have an external power source or a potentiometer, you can ground the pin and check the measurements settles to around 0 counts, or connect VDDA to the pin and check the measurements saturates at 2047 counts.
You can debug the example to step through the code. In the IDE, use the <Application Name> Debug (KitProg3_MiniProg4) configuration in the Quick Panel. For details, see the "Program and debug" section in the Eclipse IDE for ModusToolbox™ software user guide.
Note: (Only while debugging) On the CM4 CPU, some code in main() may execute before the debugger halts at the beginning of main(). This means that some code executes twice – once before the debugger stops execution, and again after the debugger resets the program counter to the beginning of main(). See KBA231071 to learn about this and for the workaround.
This code example implements two new middleware:
- AMux: a wrapper to the HSIOM registers to establish connections to the global analog mux A or B. It also supports DMA to update the internal connections without CPU intervention.
- Sampler: it adds DMA support to move data from a single channel ADC to an array of samples. It also has an internal timer to trigger the SAR ADC periodically and an external DMA (in this example, the AMux DMA).
In this example, the application samples 24 channels and prints their count values to the console terminal.
An overall block diagram of this code example is shown below:
Figure 2. Block diagram
The user is responsible to configure and initialize the SAR ADC and establish the trigger connections between the SAR ADC, the Timer and DMAs. However, the DMA and Timer configuration is handled by the Sampler and AMux middleware. It is assumed that the Timer's clock uses the maximum peripheral frequency.
The user also needs to establish the AMux switch connections between the LEFT and RIGHT side of the analog muxes. As a recommendation, the user can use the device-configurator to connect the SAR ADC to the furthest pin, so the tool sets automatically the connections. The SAR ADC shall be configured to only use one channel. If the device is configured to use more than one channel, any readings from the additional channels has to be done outside of the scope of the Sampler.
When connecting a port using the AMux_AddPort() function, not all pins need to be connected to the AMux. In case a given pin is not connected, you might only use that pin as a GPIO controlled by the CPU. No connections to any peripheral are allowed, since the HSIOM register selection is set to ZERO when not connected, which translates to GPIO controlled by the CPU.
When using the Sampler middleware, the Sampler_SetScanRate() function requires to provide the SAR ADC sampling rate and the acquisition time. Both of these information are provided by the SAR ADC parameters in the device-configurator. The Achieved Free-Run Scan Rate (sps) shall be always higher than the value provided to the Sampler_SetScanRate() function. And the Achieved aquisition time (ns) shall be always smaller or equal than the value provided to the Sampler_SetScanRate().
Currently, the code example supports up to 32 channels for muxing and sampling. If you want to change the number of muxing/sampling channels, add the definition of the AMUX_MAX_NUM_CONNECTIONS and SAMPLER_MAX_NUM_CHANNELS to the makefile. It can support up to 255 channels.
Table 1. Application resources
| Resource | Alias/object | Purpose |
|---|---|---|
| SAR ADC (PDL) | CYBSP_ADC | SAR ADC |
| Timer (PDL) | CYBSP_Timer | Timer to periodicaly trigger the SAR ADC and DMA |
| DataWire (PDL) | CYBSP_DMA_AMUX | DMA to update the analog mux switches |
| DataWire (PDL) | CYBSP_DMA_ADC | DMA to update the SAR ADC measurements |
| Resources | Links |
|---|---|
| Application notes | AN228571 – Getting started with PSoC™ 6 MCU on ModusToolbox™ software AN215656 – PSoC™ 6 MCU: Dual-CPU system design AN234334 – Getting started with XMC7000 MCU on ModusToolbox™ software |
| Code examples | Using ModusToolbox™ software on GitHub |
| Device documentation | PSoC™ 6 MCU datasheets PSoC™ 6 MCU technical reference manuals XMC7000 MCU datasheets XMC7000 technical reference manuals AIROC™ CYW20829 Bluetooth® LE SoC |
| Development kits | Select your kits from the Evaluation board finder |
| Libraries on GitHub | mtb-hal-cat1 – Hardware abstraction layer (HAL) library retarget-io – Utility library to retarget STDIO messages to a UART port |
| Middleware on GitHub | capsense – CAPSENSE™ library and documents psoc6-middleware – Links to all PSoC™ 6 MCU middleware |
| Tools | Eclipse IDE for ModusToolbox™ software – ModusToolbox™ software is a collection of easy-to-use software and tools enabling rapid development with Infineon MCUs, covering applications from embedded sense and control to wireless and cloud-connected systems using AIROC™ Wi-Fi and Bluetooth® connectivity devices. |
Infineon provides a wealth of data at www.infineon.com to help you select the right device, and quickly and effectively integrate it into your design.
For PSoC™ 6 MCU devices, see How to design with PSoC™ 6 MCU - KBA223067 in the Infineon Developer community.
Document title: CCE237994 - PSoC 6 MCU: Extending the number of SAR ADC channels
| Version | Description of change |
|---|---|
| 1.0.0 | New community code example |
© Cypress Semiconductor Corporation, 2020-2023. This document is the property of Cypress Semiconductor Corporation, an Infineon Technologies company, and its affiliates ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress shall have no liability arising out of any security breach, such as unauthorized access to or use of a Cypress product. CYPRESS DOES NOT REPRESENT, WARRANT, OR GUARANTEE THAT CYPRESS PRODUCTS, OR SYSTEMS CREATED USING CYPRESS PRODUCTS, WILL BE FREE FROM CORRUPTION, ATTACK, VIRUSES, INTERFERENCE, HACKING, DATA LOSS OR THEFT, OR OTHER SECURITY INTRUSION (collectively, "Security Breach"). Cypress disclaims any liability relating to any Security Breach, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any Security Breach. In addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. "High-Risk Device" means any device or system whose failure could cause personal injury, death, or property damage. Examples of High-Risk Devices are weapons, nuclear installations, surgical implants, and other medical devices. "Critical Component" means any component of a High-Risk Device whose failure to perform can be reasonably expected to cause, directly or indirectly, the failure of the High-Risk Device, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any use of a Cypress product as a Critical Component in a High-Risk Device. You shall indemnify and hold Cypress, including its affiliates, and its directors, officers, employees, agents, distributors, and assigns harmless from and against all claims, costs, damages, and expenses, arising out of any claim, including claims for product liability, personal injury or death, or property damage arising from any use of a Cypress product as a Critical Component in a High-Risk Device. Cypress products are not intended or authorized for use as a Critical Component in any High-Risk Device except to the limited extent that (i) Cypress’s published data sheet for the product explicitly states Cypress has qualified the product for use in a specific High-Risk Device, or (ii) Cypress has given you advance written authorization to use the product as a Critical Component in the specific High-Risk Device and you have signed a separate indemnification agreement.
Cypress, the Cypress logo, and combinations thereof, WICED, ModusToolbox, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress or a subsidiary of Cypress in the United States or in other countries. For a more complete list of Cypress trademarks, visit www.infineon.com. Other names and brands may be claimed as property of their respective owners.