Makefile

################################################################################
# File Name: makefile
#
# Description: makefile of the trapezoidal 6EDL7141 shunt application
#
# Related Document: See README.md
#
#
################################################################################
# Copyright 2022, Cypress Semiconductor Corporation (an Infineon company) or
# an affiliate of Cypress Semiconductor Corporation.  All rights reserved.
#
# This software, including source code, documentation and related
# materials ("Software") is owned by Cypress Semiconductor Corporation
# or one of its affiliates ("Cypress") and is protected by and subject to
# worldwide patent protection (United States and foreign),
# United States copyright laws and international treaty provisions.
# Therefore, you may use this Software only as provided in the license
# agreement accompanying the software package from which you
# obtained this Software ("EULA").
# If no EULA applies, Cypress hereby grants you a personal, non-exclusive,
# non-transferable license to copy, modify, and compile the Software
# source code solely for use in connection with Cypress's
# integrated circuit products.  Any reproduction, modification, translation,
# compilation, or representation of this Software except as specified
# above is prohibited without the express written permission of Cypress.
#
# Disclaimer: THIS SOFTWARE IS PROVIDED AS-IS, WITH NO WARRANTY OF ANY KIND,
# EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, NONINFRINGEMENT, IMPLIED
# WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress
# reserves the right to make changes to the Software without notice. Cypress
# does not assume any liability arising out of the application or use of the
# Software or any product or circuit described in the Software. Cypress does
# not authorize its products for use in any products where a malfunction or
# failure of the Cypress product may reasonably be expected to result in
# significant property damage, injury or death ("High Risk Product"). By
# including Cypress's product in a High Risk Product, the manufacturer
# of such system or application assumes all risk of such use and in doing
# so agrees to indemnify Cypress against all liability.
################################################################################


################################################################################
# Basic Configuration
################################################################################
##
# Type of ModusToolbox Makefile Options include:
#
# COMBINED    -- Top Level Makefile usually for single standalone application
# APPLICATION -- Top Level Makefile usually for multi project application
# PROJECT     -- Project Makefile under Application
#
MTB_TYPE=COMBINED

# Target board/hardware (BSP).
# To change the target, it is recommended to use the Library manager
# ('make modlibs' from command line), which will also update Eclipse IDE launch
# configurations. If TARGET is manually edited, ensure TARGET_<BSP>.mtb with a
# valid URL exists in the application, run 'make getlibs' to fetch BSP contents
# and update or regenerate launch configurations for your IDE.
TARGET=EVAL_6EDL7141_TRAP_1SH

# Name of application (used to derive name of final linked file).
#
# If APPNAME is edited, ensure to update or regenerate launch
# configurations for your IDE.
APPNAME=mtb-example-xmc-6edl7141-trapezoidal-1-shunt

# Name of toolchain to use. Options include:
#
# GCC_ARM -- GCC provided with ModusToolbox IDE
# ARM     -- ARM Compiler (must be installed separately)
# IAR     -- IAR Compiler (must be installed separately)
#
# See also: CY_COMPILER_PATH below
TOOLCHAIN=GCC_ARM

# Default build configuration. Options include:
#
# Debug -- build with minimal optimizations, focus on debugging.
# Release -- build with full optimizations
# Custom -- build with custom configuration, set the optimization flag in CFLAGS
#
# If CONFIG is manually edited, ensure to update or regenerate launch configurations
# for your IDE.
CONFIG=Debug

# If set to "true" or "1", display full command-lines when building.
VERBOSE=


################################################################################
# Advanced Configuration
################################################################################

# Enable optional code that is ordinarily disabled by default.
#
# Available components depend on the specific targeted hardware and firmware
# in use. In general, if you have
#
#    COMPONENTS=foo bar
#
# ... then code in directories named COMPONENT_foo and COMPONENT_bar will be
# added to the build
#
COMPONENTS=

# Like COMPONENTS, but disable optional code that was enabled by default.
DISABLE_COMPONENTS=

# By default the build system automatically looks in the Makefile's directory
# tree for source code and builds it. The SOURCES variable can be used to
# manually add source code to the build process from a location not searched
# by default, or otherwise not found by the build system.
SOURCES=

# Like SOURCES, but for include directories. Value should be paths to
# directories (without a leading -I).
INCLUDES=

# Add additional defines to the build process (without a leading -D).
DEFINES += UCPROBE_ENABLE=1             # Disable(0)/Enable(1) GUI command scheduler and uCProbe scope

# 
# PROGRAM_DEFAULT_PARAM=1:  FW will write default motor and 6EDL7141 parameter to flash at power up;
#                           use without BPA Motor Control GUI
# PROGRAM_DEFAULT_PARAM=0:  BPA Motor Control GUI will write motor and 6EDL7141 parameters to the device;
#                           use with BPA Motor Control GUI
# 
DEFINES += PROGRAM_DEFAULT_PARAM=0


# Select softfp or hardfp floating point. Default is softfp.
VFP_SELECT=

# Additional / custom C compiler flags.
#
# NOTE: Includes and defines should use the INCLUDES and DEFINES variable
# above.
CFLAGS= 

# Additional / custom C++ compiler flags.
#
# NOTE: Includes and defines should use the INCLUDES and DEFINES variable
# above.
CXXFLAGS=

# Additional / custom assembler flags.
#
# NOTE: Includes and defines should use the INCLUDES and DEFINES variable
# above.
ASFLAGS=

# Additional / custom linker flags.
LDFLAGS=

# Additional / custom libraries to link in to the application.
LDLIBS=

# Path to the linker script to use (if empty, use the default linker script).
LINKER_SCRIPT=

# Custom pre-build commands to run.
PREBUILD=

# Custom post-build commands to run.
POSTBUILD= 


################################################################################
# Paths
################################################################################

# Relative path to the project directory (default is the Makefile's directory).
#
# This controls where automatic source code discovery looks for code.
CY_APP_PATH=

# Relative path to the shared repo location.
#
# All .mtb files have the format, <URI>#<COMMIT>#<LOCATION>. If the <LOCATION> field
# begins with $$ASSET_REPO$$, then the repo is deposited in the path specified by
# the CY_GETLIBS_SHARED_PATH variable. The default location is one directory level
# above the current app directory.
# This is used with CY_GETLIBS_SHARED_NAME variable, which specifies the directory name.
CY_GETLIBS_SHARED_PATH=../

# Directory name of the shared repo location.
#
CY_GETLIBS_SHARED_NAME=mtb_shared

# Absolute path to the compiler's "bin" directory.
#
# The default depends on the selected TOOLCHAIN (GCC_ARM uses the ModusToolbox
# IDE provided compiler by default).
CY_COMPILER_PATH=


# Locate ModusToolbox IDE helper tools folders in default installation
# locations for Windows, Linux, and macOS.
CY_WIN_HOME=$(subst \,/,$(USERPROFILE))
CY_TOOLS_PATHS ?= $(wildcard \
    $(CY_WIN_HOME)/ModusToolbox/tools_* \
    $(HOME)/ModusToolbox/tools_* \
    /Applications/ModusToolbox/tools_*)

# If you install ModusToolbox IDE in a custom location, add the path to its
# "tools_X.Y" folder (where X and Y are the version number of the tools
# folder). Make sure you use forward slashes.
CY_TOOLS_PATHS+=

# Default to the newest installed tools folder, or the users override (if it's
# found).
CY_TOOLS_DIR=$(lastword $(sort $(wildcard $(CY_TOOLS_PATHS))))

ifeq ($(CY_TOOLS_DIR),)
$(error Unable to find any of the available CY_TOOLS_PATHS -- $(CY_TOOLS_PATHS). On Windows, use forward slashes.)
endif

$(info Tools Directory: $(CY_TOOLS_DIR))

include $(CY_TOOLS_DIR)/make/start.mk