CY8CEVAL-062S2-CYW955513SDM2WLIPA BSP

Overview

The CY8CEVAL-062S2 PSOC™ 62S2 Evaluation Kit enables you to evaluate and develop applications using PSOC™ 62 MCU. The PSOC™ 62S2 evaluation kit features an M.2 interface that enables you to connect the supported M.2 radio cards based on AIROC™ Wi-Fi/Bluetooth® combo devices. It comes with industry-leading CAPSENSE™ for touch buttons and slider, on-board debugger/programmer with KitProg3, microSD card interface, 512-Mb Quad-SPI NOR flash, PDM-PCM microphone interface, mikroBUS add-on board interface for peripheral expansion, OPTIGA Trust M device.
Note: CY8CEVAL-062S2-CYW955513SDM2WLIPA is the board support package for the PSOC™ 62S2 Evaluation Kit in combination with the IFX CYW955513SDM2WLIPA Wi-Fi/Bluetooth® M.2 radio module and supports PSOC™ 6 MCU examples and Wi-Fi/Bluetooth® connectivity examples.

To use code from the BSP, simply include a reference to cybsp.h.

Features

Kit Features:

Support of up to 2MB Flash and 1MB SRAM
Dedicated M.2 interface to connect with M.2 radio modules based on AIROC™ Wi-Fi/Bluetooth® combo devices.
mikroBUS add-on board interface for peripheral expansion.
Delivers dual-cores, with a 150-MHz Arm® Cortex®-M4 as the primary application processor and a 100-MHz Arm® Cortex®-M0+ as the secondary processor for low-power operations.
Supports Full-Speed USB, capacitive-sensing with CAPSENSE™, a PDM-PCM digital microphone interface, a Quad- SPI interface, 13 serial communication blocks, 7 programmable analog blocks, and 56 programmable digital blocks.

Kit Contents:

PSOC™ 62S2 Evaluation Board
USB Type-A to Micro-B cable
Four jumper wires (4 inches each)
Two jumper wires (5 inches each)
Quick start guide

BSP Configuration

The BSP has a few hooks that allow its behavior to be configured. Some of these items are enabled by default while others must be explicitly enabled. Items enabled by default are specified in the bsp.mk file. The items that are enabled can be changed by creating a custom BSP or by editing the application makefile.

Components:

Device specific category reference (e.g.: CAT1) - This component, enabled by default, pulls in any device specific code for this board.

Defines:

CYBSP_WIFI_CAPABLE - This define, disabled by default, causes the BSP to initialize the interface to an onboard wireless chip if it has one.
CY_USING_HAL - This define, enabled by default, specifies that the HAL is intended to be used by the application. This will cause the BSP to include the applicable header file and to initialize the system level drivers.
CYBSP_CUSTOM_SYSCLK_PM_CALLBACK - This define, disabled by default, causes the BSP to skip registering its default SysClk Power Management callback, if any, and instead to invoke the application-defined function cybsp_register_custom_sysclk_pm_callback to register an application-specific callback.

Clock Configuration

Clock	Source	Output Frequency
FLL	IMO	100.0 MHz
PLL	IMO	48.0 MHz
CLK_HF0	CLK_PATH0	100 MHz

Power Configuration

System Active Power Mode: LP
System Idle Power Mode: Deep Sleep
VDDA Voltage: 3300 mV
VDDD Voltage: 3300 mV

See the BSP Setttings for additional board specific configuration settings.

API Reference Manual

The CY8CEVAL-062S2-CYW955513SDM2WLIPA Board Support Package provides a set of APIs to configure, initialize and use the board resources.

See the BSP API Reference Manual for the complete list of the provided interfaces.

More information

© Cypress Semiconductor Corporation (an Infineon company) or an affiliate of Cypress Semiconductor Corporation, 2019-2025.

License

Infineon/TARGET_CY8CEVAL-062S2-CYW955513SDM2WLIPA

About

Resources

License

Stars

Watchers

Forks

Releases

Packages 0

Languages

Packages