Skip to content
Permalink
40ddfe88e5
Switch branches/tags

Name already in use

A tag already exists with the provided branch name. Many Git commands accept both tag and branch names, so creating this branch may cause unexpected behavior. Are you sure you want to create this branch?

TARGET_CY8CKIT-064S0S2-4343W/README.md

Go to file
 
 
Cannot retrieve contributors at this time
CY8CKIT-064S0S2-4343W BSP Overview Features Kit Features: Kit Contents: BSP Configuration Clock Configuration Power Configuration API Reference Manual More information
74 lines (50 sloc) 3.8 KB
Raw Blame

CY8CKIT-064S0S2-4343W BSP

Overview

The CY8CKIT-064S0S2-4343W PSoC™ 64 Standard Secure - AWS Wi-Fi BT Pioneer Kit is a low-cost hardware platform that enables design and debug of PSoC™ 64 MCUs. It comes with a Murata LBEE5KL1DX Module (CYW4343W Wi-Fi + Bluetooth Combo Chip), industry-leading CAPSENSE™ for touch buttons and slider, on-board debugger/programmer with KitProg3, microSD card interface, 512-Mb Quad-SPI NOR flash, 4-Mbit Quad-SPI F-RAM and PDM-PCM microphone interface.

To use code from the BSP, simply include a reference to cybsp.h.

Features

Kit Features:

  • Support of up to 2MB Flash and 1MB SRAM
  • Dedicated SDHC to interface with WICED wireless devices.
  • Delivers dual-cores, with a 150-MHz Arm® Cortex®-M4 as the primary application processor and a 100-MHz Arm® Cortex®-M0+ as the secondary processor for low-power operations.
  • Supports Full-Speed USB, capacitive-sensing with CAPSENSE, a PDM-PCM digital microphone interface, a Quad- SPI interface, 13 serial communication blocks, 7 programmable analog blocks, and 56 programmable digital blocks.

Kit Contents:

  • PSoC™ 64 Wi-Fi BT Pioneer Board
  • USB Type-A to Micro-B cable
  • Quick Start Guide
  • Four jumper wires (4 inches each)
  • Two jumper wires (5 inches each)

BSP Configuration

The BSP has a few hooks that allow its behavior to be configured. Some of these items are enabled by default while others must be explicitly enabled. Items enabled by default are specified in the CY8CKIT-064S0S2-4343W.mk file. The items that are enabled can be changed by creating a custom BSP or by editing the application makefile.

Components:

  • Device specific category reference (e.g.: CAT1) - This component, enabled by default, pulls in any device specific code for this board.

Defines:

  • CYBSP_WIFI_CAPABLE - This define, disabled by default, causes the BSP to initialize the interface to an onboard wireless chip if it has one.
  • CY_USING_HAL - This define, enabled by default, specifies that the HAL is intended to be used by the application. This will cause the BSP to include the applicable header file and to initialize the system level drivers.
  • CYBSP_CUSTOM_SYSCLK_PM_CALLBACK - This define, disabled by default, causes the BSP to skip registering its default SysClk Power Management callback, if any, and instead to invoke the application-defined function cybsp_register_custom_sysclk_pm_callback to register an application-specific callback.

Clock Configuration

Clock Source Output Frequency
FLL IMO 100.0 MHz
PLL IMO 48.0 MHz
CLK_HF0 CLK_PATH0 100 MHz

Power Configuration

  • System Active Power Mode: LP
  • System Idle Power Mode: Deep Sleep
  • VDDA Voltage: 3300 mV
  • VDDD Voltage: 3300 mV

See the BSP Setttings for additional board specific configuration settings.

API Reference Manual

The CY8CKIT-064S0S2-4343W Board Support Package provides a set of APIs to configure, initialize and use the board resources.

See the BSP API Reference Manual for the complete list of the provided interfaces.

More information

© Cypress Semiconductor Corporation (an Infineon company) or an affiliate of Cypress Semiconductor Corporation, 2019-2022.