This code example demonstrates the capture feature of Capture and Compare Unit 8 (CCU8) slices available in XMC™ MCU.
The code example uses two CCU8 slices of the XMC™ MCU:
- One slice configured as a PWM generator. The generated signal has a frequency of 2 Hz and 50% duty cycle.
- One slice configured in the capture mode. It will capture the timer value on the rising and falling edges of the generated PWM.
Provide feedback on this code example.
- ModusToolbox™ v3.0 or later (tested with v3.1)
- SEGGER J-Link software
- Programming language: C
- Associated parts: All XMC™ MCU parts
- GNU Arm® Embedded Compiler v11.3.1 (
GCC_ARM) – Default value ofTOOLCHAIN
- XMC1300 Boot Kit (
KIT_XMC13_BOOT_001) - XMC1400 Boot Kit (
KIT_XMC14_BOOT_001) - XMC4200 Platform2GO XTREME Kit (
KIT_XMC_PLT2GO_XMC4200) - XMC4300 Relax EtherCAT Kit (
KIT_XMC43_RELAX_ECAT_V1) - XMC4400 Platform2GO XTREME Kit (
KIT_XMC_PLT2GO_XMC4400) - XMC4500 Relax Kit (
KIT_XMC45_RELAX_V1) - XMC4700 Relax Kit (
KIT_XMC47_RELAX_V1) - Default value ofTARGET - XMC4800 Relax EtherCAT Kit (
KIT_XMC48_RELAX_ECAT_V1)
This example uses the board's default configuration. See the kit user guide to ensure that the board is configured correctly.
See the ModusToolbox™ tools package installation guide for information about installing and configuring the tools package.
Install a terminal emulator if you don't have one. Instructions in this document use Tera Term.
This example requires no additional software or tools.
The ModusToolbox™ tools package provides the Project Creator as both a GUI tool and a command line tool.
Use Project Creator GUI
-
Open the Project Creator GUI tool.
There are several ways to do this, including launching it from the dashboard or from inside the Eclipse IDE. For more details, see the Project Creator user guide (locally available at {ModusToolbox™ install directory}/tools_{version}/project-creator/docs/project-creator.pdf).
-
On the Choose Board Support Package (BSP) page, select a kit supported by this code example. See Supported kits.
Note: To use this code example for a kit not listed here, you may need to update the source files. If the kit does not have the required resources, the application may not work.
-
On the Select Application page:
a. Select the Applications(s) Root Path and the Target IDE.
Note: Depending on how you open the Project Creator tool, these fields may be pre-selected for you.
b. Select this code example from the list by enabling its check box.
Note: You can narrow the list of displayed examples by typing in the filter box.
c. (Optional) Change the suggested New Application Name and New BSP Name.
d. Click Create to complete the application creation process.
Use Project Creator CLI
The 'project-creator-cli' tool can be used to create applications from a CLI terminal or from within batch files or shell scripts. This tool is available in the {ModusToolbox™ install directory}/tools_{version}/project-creator/ directory.
Use a CLI terminal to invoke the 'project-creator-cli' tool. On Windows, use the command-line 'modus-shell' program provided in the ModusToolbox™ installation instead of a standard Windows command-line application. This shell provides access to all ModusToolbox™ tools. You can access it by typing "modus-shell" in the search box in the Windows menu. In Linux and macOS, you can use any terminal application.
The following example clones the "CCU8 capture" application with the desired name "CCU8_capture" configured for the KIT_XMC47_RELAX_V1 BSP into the specified working directory, C:/mtb_projects:
project-creator-cli --board-id KIT_XMC47_RELAX_V1 --app-id mtb-example-xmc-ccu8-capture --user-app-name CCU8_capture --target-dir "C:/mtb_projects"
The 'project-creator-cli' tool has the following arguments:
| Argument | Description | Required/optional |
|---|---|---|
--board-id |
Defined in the field of the BSP manifest | Required |
--app-id |
Defined in the field of the CE manifest | Required |
--target-dir |
Specify the directory in which the application is to be created if you prefer not to use the default current working directory | Optional |
--user-app-name |
Specify the name of the application if you prefer to have a name other than the example's default name | Optional |
Note: The project-creator-cli tool uses the
git cloneandmake getlibscommands to fetch the repository and import the required libraries. For details, see the "Project creator tools" section of the ModusToolbox™ tools package user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mtb_user_guide.pdf).
After the project has been created, you can open it in your preferred development environment.
Eclipse IDE
If you opened the Project Creator tool from the included Eclipse IDE, the project will open in Eclipse automatically.
For more details, see the Eclipse IDE for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_ide_user_guide.pdf).
Visual Studio (VS) Code
Launch VS Code manually, and then open the generated {project-name}.code-workspace file located in the project directory.
For more details, see the Visual Studio Code for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_vscode_user_guide.pdf).
Keil µVision
Double-click the generated {project-name}.cprj file to launch the Keil µVision IDE.
For more details, see the Keil µVision for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_uvision_user_guide.pdf).
IAR Embedded Workbench
Open IAR Embedded Workbench manually, and create a new project. Then select the generated {project-name}.ipcf file located in the project directory.
For more details, see the IAR Embedded Workbench for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_iar_user_guide.pdf).
Command line
If you prefer to use the CLI, open the appropriate terminal, and navigate to the project directory. On Windows, use the command-line 'modus-shell' program; on Linux and macOS, you can use any terminal application. From there, you can run various make commands.
For more details, see the ModusToolbox™ tools package user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mtb_user_guide.pdf).
-
Connect the board to your PC using a Micro-USB cable through the debug USB connector.
-
Program the board using one of the following:
Using Eclipse IDE
-
Select the application project in the Project Explorer.
-
In the Quick Panel, scroll down, and click <Application Name> Program (JLink).
In other IDEs
Follow the instructions in your preferred IDE.
Using CLI
From the terminal, execute the
make programcommand to build and program the application using the default toolchain to the default target. The default toolchain is specified in the application's Makefile but you can override this value manually:make program TOOLCHAIN=<toolchain>Example:
make program TOOLCHAIN=GCC_ARM -
-
An LED connected to the respective GPIO pin blinks. See the following table for kit - GPIO mapping.
Kit GPIO pin XMC1300 boot kit P0.0 XMC1400 relax kit P4.0 XMC4200 Platform2GO XTREME kit P0.1 XMC4300 relax EtherCAT kit P0.6 XMC4400 Platform2GO XTREME kit P0.6 XMC4500 relax kit P0.5 XMC4700 relax kit P5.8 XMC4800 relax EtherCAT kit P5.8
-
The UART peripheral is configured with the following settings:
-
Baud rate (bps): 115200
-
Word length: 8 bits
-
Stop bit(s): 1 bit
-
Parity mode: No parity
-
Flow control: None
-
Confirm that log messages appear as follows:
Figure 1. Log messages
You can debug the example to step through the code.
In Eclipse IDE
Use the **\ Debug (JLink)** configuration in the **Quick Panel**. For details, see the "Program and debug" section in the [Eclipse IDE for ModusToolbox™ user guide](https://www.infineon.com/MTBEclipseIDEUserGuide).In other IDEs
Follow the instructions in your preferred IDE.
This example demonstrates the capture functionality of the CCU8 peripheral present in XMC™ MCU. It consists of two slices: the first slice is configured to generate a PWM output signal. This signal is used in the second slice, which captures the timer value at every rising edge and falling edge of the capture trigger signal. In addition, two source events to capture the signal are defined. 'Event 0' triggers a capture on the rising edge; 'Event 1' triggers a capture on the falling edge. These two events are continuously monitored in the main function to detect and show the captured value and reset the events.
The project uses a custom design.modus file because the following settings are modified in the default design.modus file.
Figure 2. USIC (UART) settings
Figure 3. UART Tx pin settings
Figure 4. UART Rx pin settings
Figure 5. LED pin settings
| Resources | Links |
|---|---|
| Code examples | Using ModusToolbox™ on GitHub |
| Device documentation | XMC1000 family datasheets XMC4000 family datasheets XMC1000 family technical reference manuals XMC4000 family technical reference manuals |
| Development kits | XMC™ eval boards |
| Libraries on GitHub | mtb-xmclib-cat3 – XMC™ peripheral driver library (XMCLib) |
| Tools | ModusToolbox™ – ModusToolbox™ software is a collection of easy-to-use libraries and tools enabling rapid development with Infineon MCUs for applications ranging from wireless and cloud-connected systems, edge AI/ML, embedded sense and control, to wired USB connectivity using PSoC™ Industrial/IoT MCUs, AIROC™ Wi-Fi and Bluetooth® connectivity devices, XMC™ Industrial MCUs, and EZ-USB™/EZ-PD™ wired connectivity controllers. ModusToolbox™ incorporates a comprehensive set of BSPs, HAL, libraries, configuration tools, and provides support for industry-standard IDEs to fast-track your embedded application development. |
Infineon provides a wealth of data at www.infineon.com to help you select the right device, and quickly and effectively integrate it into your design.
For XMC™ MCU devices, see 32-bit XMC™ industrial microcontroller based on Arm® Cortex®-M.
Document title: CE232587 - XMC™ MCU: CCU8 capture
| Version | Description of change |
|---|---|
| 1.0.0 | New code example |
| 1.0.1 | Updated README |
| 1.1.0 | Added support for more kits |
| 2.0.0 | Updated to support ModusToolbox™ v3.0; CE will not be backwards compatible with previous versions of ModusToolbox™ |
| 2.1.0 | Added support for new kits and CCU8 personality |
| 2.1.1 | Updated README |
| 2.2.0 | Minor improvements |
All other trademarks or registered trademarks referenced herein are the property of their respective owners.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Infineon is under license.
© 2024 Infineon Technologies AG
All Rights Reserved.
The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party.
For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com).
Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.